+86-577-85883661
MVR Rising Film Evaporator
video
MVR Rising Film Evaporator

MVR Rising Film Evaporator

An MVR rising film evaporator that recycles secondary vapor through mechanical recompression, converting recovered energy into a reusable heating source – reducing fresh steam dependence while maintaining continuous, controlled concentration.
Send Inquiry
Product Details ofMVR Rising Film Evaporator

MVR

 

An MVR rising film evaporator that recycles secondary vapor through mechanical recompression, converting recovered energy into a reusable heating source – reducing fresh steam dependence while maintaining continuous, controlled concentration.

 

Technical Specifications

 

Parameter

Typical / Available Specification

Evaporation Capacity

0.5–10 t/h

Feed Capacity

0.6–12 t/h

Evaporation Temperature

40–100 °C

Typical Operating Temperature

60–90 °C

Temperature Rise by MVR Compressor

5–20 °C

Operating Vacuum

−0.05 to −0.09 MPa

Evaporator Type

Rising Film

Heating Surface Area

20–500 m²

Heat Transfer Coefficient

1,000–2,500 W/m²·K

Specific Energy Consumption

15–35 kWh/t water evaporated

Fresh Steam Consumption

≤0.05 t/t water evaporated after start-up

Compressor Type

Roots / Centrifugal

Compressor Pressure Rise

15–70 kPa

Compressor Pressure Ratio

Approx. 1.15–1.50 for centrifugal; 1.50–3.00 for Roots

Concentration Range

Engineered according to feed properties and target concentration

Heating Tube Material

SS304 / SS316L

Product-Contact Material

SS304 / SS316L

Vapor-Liquid Separator

Vertical centrifugal / gravity separation

Condensate System

Integrated condensate collection and discharge

Control System

PLC / DCS

 

MVR Evaporation with Recovered Vapor Energy

 

Unlike conventional evaporation systems that discharge secondary vapor after heat transfer, the MVR process captures and compresses this vapor before returning it to the heating system.

 

Secondary Vapor Recovery:The vapor generated during evaporation is collected instead of being treated only as waste heat.


Mechanical Recompression:A vapor compressor increases the pressure and corresponding temperature of the recovered vapor so it can be reused as the heating medium.


Closed Thermal Cycle:The recompressed vapor returns to the evaporator heating side, creating a continuous cycle of evaporation, vapor recovery and heat reuse.

 

Rising Film Evaporation for Rapid Vapor-Liquid Movement

 

The rising-film configuration uses vapor generation inside the heating tubes to drive the liquid upward, forming a rising liquid film during evaporation.

 

Bottom-Feed Heating:Feed liquid enters the lower section of the vertical heating tubes and is heated toward its boiling condition.

 

Vapor-Driven Film Formation:As evaporation begins, generated vapor moves upward at high velocity and carries the liquid upward along the tube wall.

 

Continuous Evaporation:The liquid film continues to evaporate as it rises through the heating tubes, promoting rapid heat and mass transfer.

 

Vapor-Liquid Separation:The vapor-liquid mixture leaves the heating section and enters the separator, where concentrated liquid and secondary vapor are separated.

 

Designed for Continuous Industrial Operation

 

Reduced Dependence on Fresh Steam:Once the MVR cycle is established, recovered vapor supplies a major portion of the ongoing heating demand, reducing reliance on external primary steam.

 

Lower Cooling Demand:Because vapor energy is reused within the process instead of being routinely condensed as waste heat, the overall utility demand can be reduced.

 

Compact Process Arrangement:MVR systems can achieve high thermal utilization within a relatively compact equipment arrangement.

 

Automated Process Control:Feed flow, evaporation conditions, vapor compression and other operating parameters can be coordinated through an automated control system.

 

Inside the MVR Rising Film Evaporator

01/

Evaporation Section:Vertical heating tubes provide the space for rising-film formation and continuous evaporation.

02/

Vapor Separator:Separates concentrated liquid from generated secondary vapor before vapor recompression.

03/

MVR Vapor Compressor:Recovers and compresses secondary vapor so its thermal energy can be reused.

04/

Condensation & Heat Recovery:Manages condensate and residual heat within the process according to the system configuration.

05/

Vacuum & Auxiliary Systems:Supports stable evaporation pressure and coordinated material movement.

06/

Control System:Coordinates material flow, pressure, temperature, compressor operation and other critical process variables.

Built for Stable Process Control

 

Energy efficiency alone does not make an industrial evaporator practical – the system must also maintain stable operating conditions. We design for:

 

Vapor Pressure Control: Stable pressure ensures the required evaporation temperature and proper compressor operating range.

 

Material Flow Control: Feed and concentrate flow remain coordinated with the evaporation load.

 

Compressor Operation: Compressor performance stays synchronized with the volume and pressure requirements of the generated vapor.

 

Automated Monitoring: Key process variables are monitored and controlled centrally to support continuous operation.

 

FAQ

 

Q: What is the role of the vapor compressor?

A: The compressor raises the pressure and temperature of secondary vapor so its recovered latent heat can be reused in the evaporation process.

Q: Can MVR evaporation operate at low temperature?

A: Yes. Under suitable vacuum and process conditions, MVR evaporation can operate at relatively low boiling temperatures. For selected applications, evaporation temperatures of ≤40°C may be achievable, depending on feed composition, concentration, vapor pressure, and required temperature lift.

Q: What type of compressor can be used?

A: Depending on operating conditions, MVR systems may use positive-displacement compressors such as Roots compressors or centrifugal compressors. The appropriate configuration depends mainly on vapor flow and required pressure rise – we help you select the right type for your process.

Q: Can the system be automated?

A: Yes. MVR systems can integrate process monitoring and automatic control for material flow, temperature, pressure, and compressor operation.

Q: Can Tanlet manufacture customized MVR evaporators?

A: Yes. We develop and manufacture customized products according to customer drawings, samples, or descriptions.

Q: What payment terms are available?

A: Payment terms are confirmed during quotation. T/T is the main payment method, with L/C also acceptable. Specific deposit and balance arrangements are confirmed with the quotation.

Hot Tags: mvr rising film evaporator, China mvr rising film evaporator manufacturers, suppliers, factory, Balanced Double Effect Evaporator, Double Effect Falling Film Evaporator, Forced Circulation Evaporator, MVR Rising Film Evaporator, Rising Film Evaporator, Single effect External Circulation Vacuum Evaporator

Send Inquiry

(0/10)

clearall