+86-577-85883661
Fully Automatic Large Pore Resin Adsorption Unit

Fully Automatic Large Pore Resin Adsorption Unit

A fully automatic macroporous resin adsorption unit that selectively separates target components from liquid extracts – enabling repeatable, industrial-scale enrichment, impurity removal, and downstream concentration of active ingredients.
Send Inquiry
Product Details ofFully Automatic Large Pore Resin Adsorption Unit

A fully automatic macroporous resin adsorption unit that selectively separates target components from liquid extracts – enabling repeatable, industrial-scale enrichment, impurity removal, and downstream concentration of active ingredients.

 

Technical Specifications

 

Parameter

Typical / Available Specification

Column Diameter

400–2000 mm

Column Straight Height

1500–5000 mm

Resin Bed Height

800–2500 mm

Resin Volume per Column

0.1–8.0 m³

Number of Columns

2–12 columns

Processing Flow Rate

1–60 m³/h

Service Flow Rate

2–10 BV/h

Design Pressure

0.3 MPa

Operating Pressure

≤0.25 MPa

Operating Temperature

5–80 °C

Vessel Material

SS304 / SS316L

Product-Contact Surface Finish

Ra ≤0.8 μm

Operating Mode

Automatic cyclic operation

 

Selective Adsorption for Complex Extract Liquids

 

Target-Component Enrichment:Macroporous resin selectively retains specific components from the feed solution while allowing other soluble substances to pass through according to their adsorption characteristics.

 

Impurity Reduction:The adsorption process separates target components from part of the unwanted soluble matrix, helping improve the purity of the recovered fraction.

 

Concentrated Product Stream:After adsorption and subsequent desorption, the target components can be collected in a more concentrated process stream for further concentration or formulation.

 

Reduced Dependence on Conventional Precipitation:Resin adsorption provides an alternative separation route for applications where conventional water extraction or alcohol precipitation does not provide the desired enrichment effect.

 

Working Process

01/

Feed Preparation
Clarified extract enters the adsorption system under controlled flow conditions, providing stable feed for the resin columns.

02/

Resin Adsorption
Feed passes through the macroporous resin bed, where target components are selectively retained.

03/

Washing
Resin bed washed to remove residual non-target substances and prepare the column for the next stage.

04/

Desorption
A suitable desorption medium is introduced to release adsorbed target components from the resin.

05/

Product Collection
The desorption fraction containing enriched target components is collected for subsequent concentration, purification, or formulation.

06/

Resin Regeneration
Resin is regenerated and prepared for another adsorption cycle – supporting repeated, continuous operation.

Multi-Column Operation for Continuous Process Management

 

A key feature of the system is its ability to coordinate multiple resin columns through automated valve and process control.

 

Series Operation:Multiple columns can be connected in series when the process requires staged adsorption or extended contact with the resin bed.

 

Parallel Operation:Parallel columns allow the process to distribute feed flow across multiple adsorption paths and support higher overall processing capacity.

 

Independent Column Control:Individual columns can be switched between adsorption, washing, desorption and regeneration states according to the process sequence.

 

Automatic Valve Switching:The control system coordinates valve positions and process timing to reduce manual intervention during repeated production cycles.

 

Fully Automatic Process Control

 

Automation is one of the defining features of this equipment, particularly where adsorption and regeneration require repeated sequencing.

 

DCS-Based Control:The current Tanlet system uses a workstation based on a DCS distributed control strategy for process monitoring, control and data acquisition.

 

Flow Monitoring:Flow transmitters can monitor process flow through the adsorption system and support stable operating conditions.

 

Pressure Monitoring:Pressure transmitters provide process feedback for monitoring pressure changes across the system.

 

Pump & Valve Coordination:The control system coordinates pumps and automatic valves according to the defined adsorption sequence.

 

Process Data Acquisition:Operating data can be collected through the control system to improve process traceability and repeatability.

 

Manufacturing & System Integration

 

Process Equipment Fabrication: Resin columns and associated equipment manufactured to your agreed technical configuration.

 

Automation Integration: Pumps, valves, transmitters, and control logic integrated into the operating system – not supplied as disconnected components.

 

Process Pipeline Integration: The adsorption unit connects seamlessly with upstream extraction and downstream concentration or drying processes.

 

Commissioning Support: System commissioning verifies process sequences, fluid distribution, valve operation, and control-system functionality.

 

FAQ

 

Q:What is a large pore resin adsorption unit?

A:It is a separation system that uses macroporous resin to selectively adsorb target components from liquid extracts, followed by washing, desorption and resin regeneration.

Q:What is the difference between resin adsorption and conventional filtration?

A:Filtration primarily separates particles according to physical size, while resin adsorption relies on selective interactions between the resin and dissolved components.

Q:Can the unit process Chinese herbal extracts?

A:Yes. Tanlet specifically positions this unit for Chinese medicine production and applications involving granules, capsules and tablets.

Q:Can the equipment be connected with an existing extraction line?

A:Yes. The adsorption unit can be incorporated between extraction and downstream concentration, drying or formulation processes according to the overall production configuration.

Q:What information is needed for an equipment quotation?

A:Useful process information includes feed composition, liquid flow rate, target components, required purification/enrichment objective, resin information if already defined, operating mode and the requirements of upstream and downstream equipment.

Q:What materials are available for the adsorption unit?

A:The main materials of construction are SS304 and SS316L stainless steel, with SS316L suitable for applications requiring higher corrosion resistance and stricter material-contact requirements.

Hot Tags: fully automatic large pore resin adsorption unit, China fully automatic large pore resin adsorption unit manufacturers, suppliers, factory, Fully Automatic Chromatography Separation Unit, Fully Automatic Large Pore Resin Adsorption Unit, purification and separation

Send Inquiry

(0/10)

clearall